Extron-electronic RSB 126 User Manual download pdf (Page 20)

SW USB Series • Operation

Operation, cont’d

3-8

SW USB Series • Operation

3-9

2. Place the DIP switches on the rear panel in the appropriate

position to enable emulation for the connected device.

The table below shows the switch positions for keyboard

and/or mouse emulation.

Sitch 1

(Mouse

Sitch 2

(Keyboard

Emulation

Off (down) Off (down) No emulation

On (up) Off (down) Emulate mouse only

Off (down) On (up) Emulate keyboard only

On (up) On (up) Emulate keyboard and

mouse

Example: In the illustration at right, emulation

is enabled for both a mouse and a keyboard.

If two standard mice or keyboards are connected to

output ports 3 and 4, and the appropriate emulation

DIP switch is set to on (up), the SW4 USB Plus

emulates a host to both ports.

When one or both DIP switches are set to on (up), host

emulation follows the attached peripheral device:

•

When the Mouse DIP switch (switch 1) is set to on

(up), the switcher emulates a host to any standard

mouse that is connected to either of the emulation

output ports (3 or 4).

•

When the Keyboard DIP switch (switch 2) is set to

on, the switcher emulates a host to any standard

keyboard that is connected to an emulation port.

•

When both DIP switches are set to on, the switcher

emulates a host to any connected standard mouse

and/or keyboard that is connected to port 3 or 4.

Supported peripheral devices

The SW4 USB Plus can emulate a host only to a standard

keyboard and a standard mouse. The emulation feature is

not supported with non-standard keyboards or mice, such as

devices that require additional drivers.

USB devices other than standard keyboards and mice can be

connected to output ports 3 and 4, but are not supported by

the emulation feature. If you plan to use such devices, set the

Host Emulation DIP switches to off. Examples of non-standard

keyboards or mice include media keyboards or ve-button mice.

Release buttons.

Press and hold simultaneously

for 5 seconds.

Exec Mode

LED lights.

EXEC

MODE

Setting executive mode

To exit executive mode, repeat the procedure described on the

previous page. When the SW USB is no longer in executive

mode, the red LED turns off.

Resetting

To reset the switcher to its factory default settings from the front

panel,

1. Disconnect power from the SW USB.

2. Press and hold the Input 1 button while applying power to

the unit.

The Input LEDs blink three times to indicate that a reset

has occurred. The input selection defaults to input 1, and

the Input 1 LED lights.

Host emulation (SW4 USB Plus only)

The SW4 USB Plus model provides host emulation to peripheral

devices on the output of the switcher. If a keyboard and/

or a mouse is connected to output port 3 or 4, and the Host

Emulation DIP switch(es) are set to on, the SW USB emulates

a host PC to the connected peripheral device. The keyboard/

mouse connected to the switcher’s port 3 or 4 still responds as if

it were attached directly to the computer on the selected input.

Host emulation allows instant communication of the emulated

ports when the SW USB switches to another input, by

eliminating the delay that normally occurs when a computer

recognizes a new device.

Setting up for host emulation

Host emulation is enabled via the Host Emulation DIP switches

on the rear panel. To enable host emulation,

1. Connect a keyboard, a mouse, or both to output port 3

and/or 4. The SW4 USB Plus can emulate a keyboard

and a mouse simultaneously. Either type of device can be

connected to either or both of the two emulation ports (3

and 4).

MOUSE

1 2

KEYBOARD

OFF

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 29 30

Comments to this Manuals

No comments

Extron-electronic RSB 126 User Manual Page 20

Comments to this Manuals

Related products and manuals for Computer Accessories Extron-electronic RSB 126