SW USB Series • Installation
Installation, cont’d
2-10
SW USB Series • Installation
2-11
The pinout for the host PC to the SW USB is shown below:
Host PC Pin Sitcher Pin
2 (Rx TX
3 (Tx Rx
5 (Gnd
_
RS-232 Pass Thru port
The RS-232 Pass Thru port allows you to loop through the
Transmit line of the RS-232 control port from the SW USB. This
enables you to send SIS commands to another Extron A/V
switcher. See chapter 4, “SIS Conguration and Control”, for
explanations of these SIS commands.
N
Only Extron products can be controlled via this port.
The SW USB sends SIS commands to the A/V switcher in the
following loop-through modes:
• Loop 1 mode (default) — In this mode, SIS commands
can be issued to the SW USB and/or passed through to a
connected A/V switcher via an RS-232 interface (such as
DataViewer or HyperTerminal) on your computer.
To enable Loop 1 mode, issue the
E
1LOOP
}
command.
• Loop 0 mode — In this mode, the input selection SIS
command
X!
! can be issued to the SW USB via contact
closure, the SW USB front panel buttons, or the RS-232
interface. The SW USB subsequently passes the command
through to a connected A/V switcher.
To enable Loop 0 mode, issue the
E
0LOOP
}
command.
N
In Loop 0 mode, you can still issue commands to the
SW USB using the front panel buttons, RS-232, or
contact closure in both loop modes. The loop mode
selection affects only commands coming through the
RS-232 Pass Thru port.
The diagram on the next page shows how to wire the SW USB’s
RS-232 Pass Thru port for use with an Extron A/V switcher.
(The SW USB’s RS-232 Pass Thru port does not have a receive
pin; therefore, it does not receive responses from the connected
A/V switcher.)
Wiring for RS-232 Communication
RS-232 port
The three-pin, 3.5 mm captive screw connector labeled “RS-232”
is used for optional RS-232 communication between the SW
USB and a PC or control system. The control system plugged
into this port can issue commands to the SW USB, which can
pass the commands through to an Extron A/V switcher that is
plugged into the RS-232 Pass Thru port.
N
Your RS-232 computer or control system should not be
one of the host devices that are being switched. Use a
separate computer for RS-232 control.
To connect your computer or control system to the RS-232
connector, use a male 9-pin, D-to-bare-wire RS-232 cable.
One end of the UC cable is terminated with a female 9-pin D
connector, and the other end is unterminated.
1. Wire the unterminated end of the RS-232 cable to one of
the provided three-pin captive screw plugs.
2. Plug the wired three-pole connector into the RS-232
receptacle on the switcher’s rear panel.
The gure below shows how to wire this connector for RS-232.
If you use cable that has a
drain wire, tie the drain wire to
ground at both ends.
Connect a ground wire between
the switcher and the computer or
control system.
RS-232
To Computer or
Control System
RS-232 Port
SW USB Switcher
Rear Ranel
RS-232 Port
Tx Rx
9 pin HD
Connector
(Rx) Receive Pin to Tr ansmit (Tx) Pin 3
Ground
(Tx) Tr ansmit Pin to Receive (Rx) Pin 2
RS-232 connector pin assignments
(1 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals