Extron electronic Fiber Optic Transmitter-Receiver Pair FOX 500 Rx User Manual download pdf

Speciﬁcations — FOX 500

Extron FOX 500 Tx, FOX 500 Rx Fiber Optic Transmitter-Receiver Pair • Specications

The FOX 500 consists of a transmitter (FOX 500 Tx) and a receiver (FOX 500 Rx) with one or two

ﬁberoptic cables linking the two units.

The analog RGB input signal is digitized pixel for pixel in the transmitter, sent digitally through the

ﬁbercable, and converted back to analog RGB in the receiver.

The analog audio signal(s) is (are) digitized in the transmitter, sent through the ﬁber cable, and

converted back to analog audio in the receiver.

Optical ﬁber interconnection between transmitter and receiver

Number/type �� 1 or 2 ﬁber optic

Only one ﬁber is required to transmit video, audio, and unidirectional data. A second ﬁber is

required to transmit return data for bidirectional control/communication.

Connectors �� 2 LC connectors

Operating distance

Singlemode �� 30 km (18�75 miles) with singlemode (SM) cables with a FOX 500 SM

Multimode �� 300 m (985') with 62�5 µm multimode (MM) cables with a FOX 500 MM

1 km (3280') with 50 µm multimode (MM) cables with a FOX 500 MM

2 km (6561') with 50 µm 2000 MHz bandwidth laser optimized multimode

cable with a FOX 500 MM

Operating distance is approximate. These are typical maximum distances that may vary depending

on factors such as ﬁber type, ﬁber bandwidth, connector splicing, losses, modal or chromatic

dispersion, environmental factors, and kinks.

Nominal peak wavelength�� 850 nm for FOX 500 MM, 1310 nm for FOX 500 SM

Data rate �� 4�25 Gbps

Transmission power

Singlemode �� -5 dBm, typical

Multimode �� -5 dBm, typical

Maximum receiver sensitivity

Singlemode �� -18 dBm, typical

Multimode �� -12 dBm, typical

Optical loss budget

Singlemode �� 13 dB, maximum

Multimode �� 7 dB, maximum

Video

Number/signal type �� 1 VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs input

1 VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs loop-through

Gain �� Unity

Pixel data bit depth �� 8 bits per channel, 3 channels (R, G, B)

Maximum resolution �� 1600x1200 @ 60 Hz, digitized pixel for pixel; higher resolutions up to

2048x1120, undersampled

Video input and loop-through — transmitter(FOX 500 Tx)

Number/signal type �� 1 VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs input

1 VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs loop-through

Connectors �� 1 x 5 female BNC or (1) female 15-pin HD for input

(1) female 15-pin HD for loop-through

Nominal level �� 0�7 Vp-p for RGB

Minimum/maximum levels �� Analog: 0�3 V to 1�5 Vp-p with no offset

Impedance �� 75 ohms

Horizontal frequency �� 24 kHz to 100 kHz

Vertical frequency �� 40 Hz to 120 Hz

Return loss �� <-40 dB @ 5 MHz

These transceivers are class 1 laser products. They meet the safety regulations of IEC-60825, FDA

21, CFR 1040.10, and FDA 21 CFR 1040.11.

1 2 3

Summary of Contents

Page 1 - Speciﬁcations — FOX 500

Speciﬁcations — FOX 5001Extron FOX 500 Tx, FOX 500 Rx Fiber Optic Transmitter-Receiver Pair • SpecicationsN The FOX 500 consists of a transmitter (FO

Page 2

Speciﬁcations — FOX 500, cont’dExtron FOX 500 Tx, FOX 500 Rx Fiber Optic Transmitter-Receiver Pair • Specications2Video output — receiver(FOX 500 Rx)

Page 3 - Control/remote

3Extron FOX 500 Tx, FOX 500 Rx Fiber Optic Transmitter-Receiver Pair • SpecicationsMaximum level (600 ohm) �� >+15 dBm, unbalanced at 1

Comments to this Manuals

No comments

Extron electronic Fiber Optic Transmitter-Receiver Pair FOX 500 Rx User Manual

Browse online or download User Manual for Video splitters Extron electronic Fiber Optic Transmitter-Receiver Pair FOX 500 Rx. Extron electronic Fiber Optic Transmitter-Receiver Pair FOX 500 Rx User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Video splitters Extron electronic Fiber Optic Transmitter-Receiver Pair FOX 500 Rx