Extron electronic Extron Electronics Projector PMK 300 User Manual download pdf

Extron Electronics, USA

1230 South Lewis Street

Anaheim, CA 92805

USA

714.491.1500

Fax 714.491.1517

Extron Electronics, Europe

Beeldschermweg 6C

3821 AH Amersfoort

The Netherlands

+31.33.453.4040

Fax +31.33.453.4050

Extron Electronics, Asia

135 Joo Seng Road, #04-01

PM Industrial Building

Singapore 368363

+65.6383.4400

Fax +65.6383.4664

Extron Electronics, Japan

Kyodo Building

16 Ichibancho

Chiyoda-ku, Tokyo 102-0082 Japan

+81.3.3511.7655

Fax +81.3.3511.7656

www.extron.com

68-993-01

Rev. B 12 05

PMK 300 Multi-Product Projector Mounting Kit

Installation Instructions

N Only VersaTools products and most IP Link products can be

mounted using the multi-product projector mounting kit.

1. If necessary, remove the feet from the bottom of the device to be

installed.

2. Mount the device(s) to any of the bracket’s three mounting

plates. The device(s) can be vertically mounted facing either

up or down, whichever is most convenient. See ﬁ gure 1 on the

other side of this card.

N On the side mounting plates, the device is typically mounted on

the outside of the bracket.

On the front mounting plate, the device is typically mounted on

the inside of the bracket.

a. For a VersaTools or IP Link device, use two supplied

4-40 x 3/16 screws in opposite (diagonal) corners to

secure the device to the bracket.

b. For a power supply, use the two included tie wraps to

strap the power supply to the bracket.

N The PMK 300 has a hole in the bottom plate that allows the

projector pole to be inserted through the center of the plate

rather than outside of the plate (see ﬁ gure 2 on the other side of

this card). To install the PMK 300 in this conﬁ guraion, slide

the bracket up from the bottom of the pole before the projector is

installed on the pole.

3. Afﬁ x the supplied rubber pad to the side of the U-bolt clamping

plate that the projector pole contacts.

4. Place the U-bolt around the ceiling pole and insert the two legs

of the U-bolt through the slotted holes on the bracket’s clamping

plate and then through the round holes on the backing brace.

For a typical (1.5“ to 2.0“ diameter) pole — The supplied U-bolt

ﬁ ts a typical ceiling pole.

For a smaller or larger pole — Locally obtain a U-bolt that ﬁ ts

the ceiling pole. The slotted holes on the bracket can accomodate

a U-bolt for pole sizes from 1.0“ to 2.5“ in diameter.

5. Secure the bracket to the U-bolt with the included hex nuts,

washers, and lock washers. Use a proper-sized socket to tighten

the hex nuts.

PMK 300 Multi-Product Projector Mounting Kit

Installation Instructions (continued)

Extron

PMK 300

Multi Product Projector

Mount Kit

U-Bolt

Rubber Pad

Backing

Brace

Clamping

Plate

U-Bolt

Extron

PMK 300

Multi Product Projector

Mount Kit

Rubber Pad

Clamping

Plate

Backing

Brace

Figure 1 Figure 2

Installation Instructions 1

Summary of Contents

Page 1 - Installation Instructions

Extron Electronics, USA1230 South Lewis StreetAnaheim, CA 92805USA714.491.1500 Fax 714.491.1517Extron Electronics, EuropeBeeldschermweg 6C3821 AH Ame

Comments to this Manuals

No comments

Extron electronic Extron Electronics Projector PMK 300 User Manual

Browse online or download User Manual for Projector accessories Extron electronic Extron Electronics Projector PMK 300. Extron electronic Extron Electronics Projector PMK 300 User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Projector accessories Extron electronic Extron Electronics Projector PMK 300